Electrical Measurements Bench Pro
(CW101)
  • Familiarization with the basics of electrical configurations.
  • Performing different AC or DC electrical configurations.
  • Understanding how to use an AC power meter.
  • Understanding how to use a DC voltmeter and DC ammeter.
  • Familiarization with electrical measurement devices such as oscilloscopes and function generators.

ON/OFF switch:

  • Current: 32 A25A

RCCB:

  • Current: 32 A
  • Poles: 2-Pole

AC/DC variable source:

  • Maximum voltage: 250V
  • Maximum current: 10A

DC fixed source

  • +3.5V, -5 V, +5 V, -12 V, +12V, -15 V, +15 V, +24 V Maximum current: 10A

AC fixed source

  • Maximum voltage: 220-240 VAC
  • Maximum current: 16 A
  • Frequency: 50 Hz

Function generator

  • 0.1 Hz to 5/12/25 MHz within 0.1 Hz Resolution
  • Sine, Square, Triangular, Noise and Arbitrary Waveform
  • 20 MSa/s Sampling Rate,10-bit Vertical Resolution and 4k Point Memory for Arbitrary Waveform
  • 1% ~ 99% adjustable duty cycle for Square Waveform

Oscilloscope

  • Analog bandwidth: 100 MHz Maximum current: 16 A
  • Rise time: 3.5 ns
  • Channels: 2
  • Maximum sampling rate: 1 GSa/s
  • Display: 7" TFT, 800x480 pixels
  • Input impedance: 1 MΩ // 16 pF
  • Horizontal scale: 1 ns/div - 100s/div
  • Vertical resolution: 1 mV/div - 10 V/div
  • Electrical Measurements Bench Pro (CW101)
  • Hard copy user manual

This bench allows trainees to perform a wide range of electrical measurements all in one place, with connecting different devices to this work bench, trainees will be able to measure current, voltage and display the corresponding waveforms. The bench is easy to use and provides the most needed measurements required for any electrical lab.

  • This training system supports single-phase supply for electrical devices and it’s purposed for carrying out electrical measurements.
  • The system is supplied with 2-pole circuit breakers in order to provide protection against overcurrent and prevent damage to the electrical components.
  • The system is also provided with a 2-pole RCCB in order to provide protection to trainees against electrical power leakage.
  • Two indication LEDs are provided within the training system, the first one is to indicate that the system is ready to operate while the second LEDs lights in case of overload protection.
  • The training system is supplied with AC and DC power supply sources. The DC power supply is provided with fixed supply terminals of different voltages and variable power supply terminals. While the AC power supply is provided fixed and variable
  • power supply terminals as well as earthing terminals for the fixed supply.
  • An autotransformer is supplied to control the voltages of the DC and AC power supply. In addition, an Alarm LED is provided in order to warn the user in case of current exceeding the limit of 10 A.
  • A fuse protection is supplied in the AC/ DC supply section to protect the system against excessive current.
  • Four 220V plugs are provided to enable trainees to connect any external devices.
  • A function generator is provided with all of its inputs and outputs ports along with USB cable port which is used to generate different types of electrical waveforms over a wide range of frequencies.
  • An Oscilloscope device is also provided in the training system with its connection ports and USB cable port in order to display and analyze waveforms.
  • Four displays are provided for the current and voltage reading of AC and DC, each display is supplied with its connecting terminals.
  • The training system is supplied with a horizontal bench where trainees can place the used equipment on it.
  • A drawer unit is supplied within the system in order to accommodate all of the used components to protect against wear and damage.
  • The training system is supplied with an ON/OFF switch and an emergency button in case of any inconvenience.