Advanced PIC Microcontroller kit
(EM - 009)
  • AI Intelligent Biped robot (EM-009)
    • 1 X Ethernet Cable
    • 3 X USB Cable
    • 1 X MicroSD Card
    • 1 X Headset
  • Hard copy user manual

Advanced PIC Microcontroller kit is a benchtop kit that tends to familiarize the trainee with the advanced topics of PIC Microcontroller, the different microcontroller components and connections. Support for three different architectures dsPIC33, PIC24 and PIC32 .The kit is designed in the form of a lightweight portable Plastic case equipped with a real microcontroller and various electronic components related to its functions to allow wide ranges of experiments. Kit is based on Microchip dsPIC/PIC Microcontroller .Kit provides a large number of interface modules with configuration switches which open a wide range of experiments . With the PICkit In-Circuit Debugger/Programmer, just what you need is a USB cable to PC, no more additional hardware components to apply programming codes . Easy to use and friendly kit

                                     
  • Embedded PICKIT programmer / debugger (access via USB port with indication LEDs)
  • Microcontrollers supported as individual modules that plugged in to the Kit, default Plug-in module with kit [PIC32MZ2064DAL169] Module with the following features:
    • Core: 200 MHz
    • 120 I/O
    • Internal DDR2 SDRAM interface
    • 3-layer Graphics Controller with up to 24-bit color support
    • High-perfoEMance 2D Graphics Processing Unit (GPU)
    • Audio Interfaces
    • USB 2.0 High-Speed On-The-Go (OTG) controller
    • 10/100 Mbps Ethernet MAC with MII and EMII interface
    • 12-bit ADC
    • CAN, UART, SPI, I2C Communication
  • The trainer is also support these families of microcontroller (not included, refer to optional section) dsPIC33, PIC24 and PIC32
  • Microcontroller working voltage selectable (+3.3 or +5V)
  • Integrated fixed DC power supply module: + 3.3V, +5V, +12V, -5V, -12V (Fuse Protected) with led indicators - accessed via 2mm sockets (for external modules)
  • Integrated variable DC power supply Module : +1.25VDC to +5VDC or -1.25VDC to -5VDC (fuse protected) with led indicators - accessed via 2mm sockets (for external modules)
  • Pullup and pulldown resistor for every microcontroller Pin (selectable between (pull-up, floating, pull-down)
  • Indication LED for every microcontroller Pin
  • Push Button for every microcontroller pin (selectable between VCC or GND signal)
  • Pin header male/female groups for every microcontroller PORT for external connections
  • Programming IDE: supports MPLAB® X integrated development environment and MikroC for PIC
  • Includes ready to run codes for all included trainer components by MicroC For PIC
  • 8 Digital switches (+3.3 or +5V) Selectable
  • Integrated pulse generator from 2 Hz : 1KHz ( level selectable +3.3V or +5V)
  • Dip switches for configuring microcontroller I/O Ports
  • 1 x AC power source socket (fuse protected) with ON/OFF switch
  • Type A Communication Kit (EM-009.1.1)
    • 1 x TFT Touch Screen
    • 1 X CAN Interface type-A plug-in module
    • 2 X UART To USB Interface Type-A Plug-in Module
    • 1 x I2C EEPROM type-A plug-in module
    • 1 X Ethernet type-A plug-in module
    • 1 X Audio In/Out type-A plug-in module
    • 1 X MicroSD Card type-A plug-in module
  • Type A Actuator Kit (EM-009.1.2)
    • 1 x Piezo buzzer type-A plug-in module
    • 1 x speaker type-A plug-in module
    • 1 x stepper motor interface Through ULN23803
    • 1 x DC motor interface
    • 1 x servo motor interface
  • Type A Sensors kit (EM-009.1.3)
    • 1 x temperature sensor LM35 type-A plug-in module
    • 1 x temperature sensor D518B20 type-A plug-in module
    • 2 x potentiometers to Simulate analog I/P To microcontroller (microcontroller connected pin selectable)
    • 5 X Type-A Plug-in Modules Holder ( For Type-A Plug-in Modules )
  • Type-B Plug-in Modules (EM-009.1.4)
    • 1 X Type-B Plug-in Modules Holder ( For Type-B Plug-in Modules )
    • 1 x USB socket type B (for direct USB connection as a host)