PIC Micro controller kit (EMB101) is a benchtop kit that tends to familiarize the trainee with the different microcontroller components and connections. The kit is designed in the form of a lightweight portable Plastic case equipped with a real microcontroller and various electronic components related to its functions to allow wide ranges of experiments. Kit is based on Microchip PIC Microcontroller .Kit provides a large number of interface modules with configuration switches which open a wide range of experiments . With the PICkit In-Circuit Debugger/Programmer, just what you need is a USB cable to PC, no more additional hardware components to apply programming codes . Easy to use and friendly kit
- PIC Microcontroller trainer consist of
- Embedded PICKIT programmer / debugger (access via USB port with indication LEDs)
- Microcontrollers supported as individual modules that plugged in to the Kit ( default Plug-in module with kit «PIC18f45k22 SMD Module )
- The trainer is also support these families of microcontroller (not included, refer to optional section) PIC18F Family (PIC10F, PIC12F, PIC16F, PIC16F Enh, PIC18F, PIC18FJ and PIC18FK)
- The trainer also Supported these families of microcontroller packages (not included , refer to optional section) (DIP40, DIP28, DIP20, DIP18, DIP14, DIP8 and SMD) Through MC Plug-in modules
- Microcontroller working voltage selectable (+3.3 or +5V)
- Integrated fixed DC power supply module: + 3.3V, +5V, +12V, -5V, -12V (Fuse Protected) with led indicators - accessed via 2mm sockets (for external modules)
- Integrated variable DC power supply Module : +1.25VDC to +5VDC or -1.25VDC to -5VDC (fuse protected) with led indicators - accessed via 2mm sockets (for external modules)
- Pullup and pulldown resistor for every microcontroller Pin (selectable between (pull-up, floating, pull-down)
- Indication LED for every microcontroller Pin
- Pushbutton for every microcontroller pin (selectable between VCC or GND signal)
- Pin header male/female groups for every microcontroller PORT for external connections
- Programming IDE: supports MPLAB® X integrated development environment and MikroC for PIC
- Includes ready to run codes for all included trainer components by MicroC For PIC
- 8 Digital switches (+3.3 or +5V) Selectable
- Integrated pulse generator from 2 Hz : 1KHz ( level selectable +3.3V or +5V)
- Dip switches for configuring microcontroller I/O Ports
- 1 x AC power source socket (fuse protected) with ON/OFF switch
- Main Kit Code : (EMB-101.1)
- Type A Communication Kit Code : (EMB-101.1.1)
- 1 x (2 x 16 LCD module) contrast adjustable via potentiometer
- 1 x (64 X 128 GLCD module) contrast adjustable via potentiometer
- 1 X UART To USB Interface Type-A Plug-in Module
- 1 x I2C EEPROM type-A plug-in module
- 1 X RS232 Interface Type-A Plug-in Module
- Type A Actuator Kit Code : (EMB-101.1.2)
- 1 x Piezo buzzer type-A plug-in module
- 1 x speaker type-A plug-in module
- 1 X seven segment type-A plug-in module
- 1 x stepper motor interface Through ULN23803
- 1 x DC motor interface
- 1 x servo motor interface
- Type A Sensors kit Code : (EMB-101.1.3)
- 1 x temperature sensor LM35 type-A plug-in module
- 1 x temperature sensor D518B20 type-A plug-in module
- 2 x potentiometers to Simulate analog I/P To microcontroller (microcontroller connected pin selectable)
- 5 X Type-A Plug-in Modules Holder ( For Type-A Plug-in Modules )
- Type-B Plug-in Modules Code : (EMB-101.1.4)
- 1 X Type-B Plug-in Modules Holder ( For Type-B Plug-in Modules )
- 1 x USB socket type B (for direct USB connection as a host)