AVR micro controller kit (EMB102) is a benchtop kit that tends to familiarize the trainee with the different microcontroller components and connections. The kit is designed in the form of a lightweight portable aluminum case equipped with a real microcontroller and various electronic components related to its functions to allow wide ranges of experiments. Kit is based on Microchip AVR Microcontroller . Kit provides a large number of interface modules with configuration switches which open a wide range of experiments . With the In-Circuit Debugger/Programmer, just what you need is a USB cable to PC, no more additional hardware components to apply programming codes . Easy to use and friendly kit.
- AVR Microcontroller trainer consist of:
- Embedded in circuit programmer /debugger (access via USB port with indication LEDs)
- Microcontrollers supported as individual modules that plugged in to the Kit (default Plug-in module with kit «ATMEGA169PA SMD Module).
- The trainer is also support these families of microcontrolller (not included, refer to optional section) (ATmega8535, ATmega32, ATmega128, ATmega2560)
- Microcontroller working voltage selectable (+3.3 or +5V)
- Integrated fixed DC power supply module: + 3.3V, +5V, +12V, -5V, -12V (Fuse Protected) with led indicators - accessed via 2mm sockets (for external modules)
- Integrated variable DC power supply module:+1.25VDC to +5VDC or -1.25VDC to - 5VDC (fuse protected) with led indicators - accessed via 2mm sockets (for external modules)
- 8 Digital switches (+3.3 or +5V) selectable
- Integrated pulse generator from2 Hz : 1KHz ( level selectable +3.3V or +5V)
- Dip switches for configuring microcontroller I/O Ports
- 1 x AC power source socket (fuse protected) With ON/OFF switch
- Pullup and pulldown resistor for every microcontroller pin (selectable between (pull-up, floating, Pull-down)
- Indication LED for every microcontroller pin
- Pushbutton for every microcontroller pin (selectable between VCC or GND signal)
- Pin header male/female groups for every microcontroller PORT for external connections
- Programming IDE: supports atmel studio 7 development environment, atmel start online tool and Mikroc For AVR
- Includes ready to run codes for all included trainer components by atmel studio
- Main Kit Code : (EMB-102.1)
- Type A Communication Kit Code : (EMB-102.1.1)
- 1 x (2 x 16 LCD Module) contrast adjustable via potentiometer
- 1 x (64 X 128 GLCD module) contrast adjustable via potentiometer
- 1 x I2C EEPROM type-a plug-in module
- 1 X RS232 Interface Type-A Plug-in Module
- 1 X UART To USB Interface Type-A Plug-in Module
- Type A Actuator Kit Code : (EMB-102.1.2)
- 1 X Seven Segment Type-A Plug-in Module
- 1 X piezo buzzer type-A plug-in module
- 1x stepper motor interface Through ULN23803.
- 1 x DC motor interface
- 1 x Servo motor interface
- Type A Sensors kit Code : (EMB-102.1.3)
- 2x potentiometers to simulate analog I/P to microcontroller (microcontroller connected pin selectable)
- 5 X Type-A Plug-in Modules Holder ( For Type-A Plug-in Modules )
- Type-B Plug-in Modules: Code : (EMB-102.1.4)
- 1 X Type-B Plug-in Modules Holder ( For Type-B Plug-in Modules )
Lot 36, 4th Industrial Zone, 6th October City, Giza, Egypt
+2(02)38335766
+2(02)38847045
