Multi-Controller kit (EMB107) is a benchtop kit that tends to familiarize the trainee with different Microcontrollers ,related components and connections. The kit is designed in the form of a lightweight portable Plastic case equipped with a real microcontrollers and various electronic components related to its functions to allow wide ranges of experiments. Kit is based on Multi-Controllers Topology with a big advantages of no requirement for hand made jumper wires connections between system components to establish the experiment. The Multi-Controller kit is based totally on the concept of plug-in, all microcontrollers modules , peripheral modules are pluggable which minimize the experiment time and provide safety to the system modules. Kit provides a large number of interface modules with configuration switches which open a wide range of experiments . CPLD module is added to give the gain of knowledge about Configurable digital logic design. With the In-Circuit Debugger/Programmer, just what you need is a USB cable to Laboratory PC, no more additional hardware components to apply programming codes .
Easy to use and friendly kit.
- Multi-Controller kit consist of
- PIC Microcontroller Plug-in Module : PIC18F45K22
- AVR Microcontroller Plug-in Module : ATMega128
- 8051 Microcontroller Plug-in Module: AT89S52
- CPLD Plug-in Module : Xilinx XCR3256XL (Support for complex asynchronous clocking)
- In-Circuit Debugger/Programmer For the supported Microcontroller Modules
- Microcontroller working voltage selectable (+3.3 or +5V)
- Integrated fixed DC power supply module:+3.3V, +5V, +12V, -5V, -12V (Fuse Protected) with led indicators - accessed via 2mm sockets (for external modules)
- Integrated variable DC power supply Module : +1.25VDC to +5VDC or -1.25VDC to -5VDC (fuse protected) with led indicators - accessed via 2mm sockets (for external modules)
- Pullup and pulldown resistor for every microcontroller Pin (selectable between (pull-up, floating, pull-down)
- Indication LED for every microcontroller Pin
- Push Button for every microcontroller pin (selectable between VCC or GND signal)
- Pin header male/female groups for every microcontroller PORT for external Connections
- Programming IDE:
- supports MPLAB® X integrated development environment and MikroC for PIC
- supports atmel studio 7 development environment, atmel start online tool and Mikroc For AVR
- supports keil for 8051
- supports ISE WebPACK for CPLD
- Includes ready to run codes for all included trainer components
- 8 Digital switches (+3.3 or +5V) Selectable
- Integrated pulse generator from 2 Hz : 1KHz ( level selectable +3.3V or +5V)
- Dip switches for configuring microcontroller I/O Ports.
- AC power source socket (fuse protected) with ON/OFF switch.
- Type A Communiction Kit (EMB107.1.1)
- 1 x (2 x 16 LCD module) contrast adjustable via potentiometer
- 1 x (64 X 128 GLCD module) contrast adjustable via potentiometer
- 1 X UART To USB Interface Type-A Plug-in Module
- 1 x I2C EEPROM type-A plug-in module
- 1 X RS232 Interface Type-A Plug-in Module
- Type A ACtuator KIt (EMB107.1.2)
- 1 x Piezo buzzer type-A plug-in module
- 1 x speaker type-A plug-in module
- 1 X seven segment type-A plug-in module
- 1 x stepper motor interface Through ULN23803
- 1 x DC motor interface
- 1 x servo motor interface
- Type A Sensors kit (EMB107.1.3)
- 1 x temperature sensor LM35 type-A plugin module
- 1 x temperature sensor D518B20 type-A plug-in module
- 2 x potentiometers to Simulate analog I/P To microcontroller (microcontroller
- connected pin selectable)
- 5 X Type-A Plug-in Modules Holder ( For Type-A Plug-in Modules )
- Type-B Plug-in Modules (EMB107.1.4)
- 1 X Type-B Plug-in Modules Holder ( For Type-B Plug-in Modules )
- 1 x USB socket type B (for direct USB connection as a host)